How much does a car lift cost? For a working shop, a 10,000 lb two-post lift lists at $6,095 on BendPak’s own site, and the full installed cost runs well past that once freight extras, concrete, an electrician, the installer and the yearly inspection show up.
Every owner I know has watched a lift get delivered at 4:55 on a Friday by a driver who made it very clear that unloading 1,768 pounds of steel was not in his job description. (I was the kid holding the shop door open. I still think about that pallet jack.)
Full disclosure: I run WickedFile. It reads the stack of invoices a purchase like this creates, so a freight surcharge or installer’s bill doesn’t get paid twice or go missing. I’ll walk you through doing it by hand first.
How much does a car lift cost by type?
These are list prices on BendPak’s two-post lift page and its sister category pages, as of November 2026. Dealers and other brands will vary. I’m using one manufacturer so you’re comparing apples to apples, not a blog’s average of averages.
| Lift type | Example model | Capacity | BendPak list price |
|---|---|---|---|
| Two-post | BendPak 10AP | 10,000 lb | $6,095 |
| Two-post, high-rise | BendPak 10APX | 10,000 lb | $6,895 |
| Two-post, heavy | BendPak 12APX | 12,000 lb | $10,495 |
| Four-post | BendPak HD-9ST | 9,000 lb | $5,995 |
| Four-post, heavy | BendPak HDS14 | 14,000 lb | $8,595 |
| Mid-rise scissor | BendPak MDS-6LPF | 6,000 lb | $7,695 |
| Full-rise scissor | BendPak SP-7XEF | 7,000 lb | $10,295 |
| Alignment (four-post) | BendPak HDS14LSX | 14,000 lb | $12,295 |
| Portable | MaxJax MAX7 Standard | 7,000 lb | $5,395 |
| In-ground | Rotary SL210 | 10,000 lb | Quote only |
In-ground lifts are the outlier. The Rotary dealer I checked lists the SL210 with “for current pricing please call or submit a quote request.” An in-ground lift means cutting into your floor, so the job is quoted for your building, not pulled off a list. I’m not going to guess at that number for you.
So how much is a car lift for a mechanic shop? For the everyday two-post bay, the lift itself starts around $6,000 at list. For a home garage, the portable and light four-post options sit in the same neighborhood, which surprises people. The difference shows up after the lift arrives.
How much does a car lift cost once it’s bolted to your floor?
The sticker is one invoice. A finished lift bay is usually several, from different vendors, arriving weeks apart.
Freight and delivery extras. BendPak’s shipping policy says most of its products ship free to eligible points in the lower 48. Then come the extras: a $95 liftgate fee if you don’t have a dock, $70 for a residential address, $75 for each redelivery, and storage at the terminal if the shipment sits. The policy also says these charges “may be added when the order is invoiced or billed after delivery.” Remember that sentence. We’ll come back to it.
Concrete. BendPak recommends test drilling existing floors and core testing for compressive strength. It says its lifts go on “concrete only,” never on hand-mixed concrete, and anchors stay at least 6 inches from expansion seams and cracks. If your slab fails, add a concrete contractor and a cure time to the budget.
Electrical. The 10AP’s power unit is 5 HP at 208-230V single phase. If the bay doesn’t have that circuit, an electrician does, and that’s a separate bill.
Installation. Some dealers install. Some subcontract it. Some leave it to you. Either way it’s a line item, and the cost depends on lift type, anchoring and how far the installer drives.
Accessories. Truck adapters, frame cradles and extra pads add up fast. BendPak’s own 10AP page lists truck and van adapter sets at $196 to $250 a set.
The annual inspection. This one never ends. More on it below.
2 post car lift space requirements: measure twice, order once
A two-post lift needs height, width and the right slab. The spec sheet tells you exactly how much. For BendPak’s 10AP, the product page lists:
- Overall height: 145 inches (just over 12 feet).
- Overall width: 135 to 145 inches.
- Drive-thru clearance: 92 to 102 inches between the columns.
- Floor to the overhead shutoff bar: 139.5 inches.
- Power: 5 HP, 208-230V, single phase.
Measure your lowest point, not your average ceiling. That means the garage door track, the tube heater and the light fixture somebody hung in 2009. A lift that fits the drawing and hits the door opener is a very expensive way to learn about door openers.
If the ceiling is tight, BendPak’s low-ceiling 9APF and 12APF models exist for exactly that reason, and they cost more. That’s a real trade-off, and it’s better to find it on paper than on the delivery truck.
The lift invoice is easy. The four bills after it are where money leaks.
Here’s where it usually falls apart. The lift invoice is big, so somebody looks at it. The smaller bills that follow don’t get the same attention.
Picture a two-bay upgrade. Two BendPak 10AP lifts at $6,095 each is $12,190 at list. Then, over the next six weeks, the shop gets:
- A freight bill with a $95 liftgate fee and a $75 redelivery, because nobody was there Friday at 4:55. That’s $170, billed after delivery.
- The installer’s invoice.
- The electrician’s invoice for two new circuits.
- An adapter order on the shop’s card, with no invoice in the office.
Every one of those is legitimate. And every one is a chance for something to go wrong:
- The late freight charge gets paid twice. Once when the carrier bills it, and again when it shows up on the dealer’s statement.
- The installer and the electrician get coded to repairs and maintenance. IRS Publication 551 says the cost basis of property includes “Freight. Installation and testing.” Code those to repairs, and your books show a cheaper lift and a weird spike in repairs that month. Your CPA will catch it at year end, if you’re lucky, and bill you for the cleanup.
- The card charge has no paperwork. Somebody bought adapters on the shop card. Six months later, nobody remembers which ones, or whether they fit.
And if the wrong lift shows up? BendPak’s shipping policy says returned merchandise “is subject to a 20% restocking fee,” plus shipping both ways. On a $6,095 lift, that’s $1,219 before the freight. That’s why the spec check above happens before the order, not after.
The bay itself costs money too. At the $165 average labor rate in accounting firm Paar Melis’s 2025 benchmark report, a bay that would bill 6 hours a day is $990 a day of labor sitting idle while you wait on an electrician. (Illustrative. Your hours are your hours.)
Treat a lift purchase like a parts order with a bigger number
A real AP process isn’t optional. It’s how every successful shop eventually runs, and the only question is whether you build it before or after a costly lesson. Equipment purchases are where shops skip it most, because they only happen every few years and feel like a one-time event.
They’re not one-time. The lift creates a paper trail for its whole life: the purchase, the freight, the install, the circuit, the adapters, and an inspection every single year.
Here’s the checklist I’d use for any lift, in plain terms:
- Before ordering: get the model’s spec sheet. Measure height, width and door clearance. Confirm the slab and the circuit.
- On the order: get a written quote listing the lift, freight terms, installation and accessories. Ask what can be “billed after delivery.”
- On delivery: note on the delivery receipt if a liftgate was used or a redelivery happened. That’s your proof when the extra charge arrives.
- As each invoice lands: file it in one folder for that purchase. Match each one to a payment. One invoice, one payment, no exceptions.
- At month end: tie the dealer’s statement to your folder. Anything on the statement you can’t match gets a phone call before you pay.
- At year end: hand your CPA the folder. Freight and installation go with the lift.
The folder is the whole trick. A $12,000 purchase with six invoices is just a parts order with commas in it. If you want the full version, here’s the accounts payable process I’d put any shop on.
Budget the annual lift inspection every year, not once
The Automotive Lift Institute’s annual inspection page is direct about it: the ANSI/ALI ALOIM:2020 standard requires that “a lift owner or employer utilize a qualified lift inspector to inspect all lifts at least annually.”
So the inspection is a recurring cost, not a one-time one. It applies to every lift in the building, old or new, any brand. Put it on the calendar the week the lift goes in, and put the cost in next year’s budget the same day.
Before you buy, check the model too. ALI says lifts that pass third-party testing to the ANSI/ALI standard get the ALI Gold Certification Label and are listed in its Directory of Certified Lifts. BendPak’s own product pages note that not all of its models are ALI certified, which is an honest thing for a manufacturer to say. Check the specific model, not the brand.
Keep the inspection report in the same folder as the purchase paperwork. ALI notes that health and safety officials “regularly check for proof of annual lift inspections and operator training” during site visits. When they ask, you want one place to look.
Software should check the lift paperwork before the last invoice gets paid
The folder and checklist above work. If you buy one lift every five years, that’s probably all you need, and I’d rather you know that.
WickedFile earns its keep when equipment buys pile on top of normal parts volume. A shop with five parts vendors, a fleet of card holders and a two-bay lift project is a lot of paper for one bookkeeper.
Here’s what WickedFile does with it:
- Reads the documents. Vendor invoices, freight bills, installer invoices, credit memos and statements, scanned or uploaded.
- Matches documents to money. It connects to QuickBooks Online and to bank and card feeds through Plaid, so a card charge for lift adapters with no invoice shows up as an exception.
- Flags the gaps. A statement line with no supporting invoice, an invoice with no accounting entry, a payment that looks like a duplicate.
- Does the same for parts. That’s the main job: matching parts invoices to repair orders in your shop management system and catching missing credits and uncredited cores.
To test it on this exact problem, use the free trial: 500 scanned pages, no credit card. Upload every invoice and statement from your last big equipment purchase, plus one month of statements from your equipment dealer and your biggest parts vendor. That’s usually well under 500 pages, and you’ll see whether anything slipped through.
What it doesn’t do: it won’t install, inspect or service your lift. It isn’t a shop management system, a payment processor or a replacement for QuickBooks and your bookkeeper. It tells you what to question before you pay. After the trial, the Grow plan is $299 a month, flat.
Upload your last equipment purchase to the free trial →
Picking a car lift for a mechanic shop comes down to the work
Two-post for general repair. Four-post for alignment and storage. Scissor for tire and quick service. In-ground for a building you plan to own for decades. Then price it from a published list, check the model in ALI’s directory, and measure your ceiling against the spec sheet.
If the lift is financed, the loan has its own paperwork. Here’s how notes payable differ from accounts payable. For the dealer’s monthly statement, vendor statement reconciliation walks through the matching. And if you’re building a new shop from scratch, the mechanic shop business plan post covers where equipment fits in the budget.
Buy the lift, check the paperwork, book the inspection. And next time the truck shows up at 4:55 on a Friday, have the forklift ready. The driver still won’t help, but at least you’ll skip the redelivery fee.
